Towering Timbers, A Block Stacking Game

Timbering Towers, a DIY oversized block stacking game is perfect for entertaining guests during barbecues and friends on game day. Jen Woodhouse of The House of Wood designed this DIY giant outdoor block stacking game–Timbering Towers–and accompanying storage crate to make it easy to bring along for tailgating.

All you’ll need is some studs lumber, common hardware and some simple tools that you can rent at The Home Depot. You can customize it with your favorite team colors or a cool design.

Towering Timbers, an Outdoor Block Stacking Game DIY

Towering Timbers, an oversized block stacking game, is a great way to entertain family and friends while tailgating or barbecuing on game day. Yard games are a must at every tailgate. This oversized outdoor game is sturdy enough to take a beating and easy to travel with, and you only need a few simple materials and tools to make it.

Tools:

Materials:

(6) 2 x 4 x 8 ft. Boards
(1) 1 x 12 x 8 ft. Board
(1) 1 x 3 x 2 ft. Board
(2) Storage Chest Handles
1 ¼-in. Exterior Pocket Screws (optional)
1 ¼-in. Exterior Wood Screws
1 ¼-in. Exterior Brad Nails
Exterior Wood Glue

Cut List:

Stacking Box Cuts:

(54) 2 x 4 x 10 ½ in.

Storage Box Cuts:

(2) 1 x 12 x 22 ½ in. (Long Sides)
(2) 1 x 12 x 13 ¾ in. (Short Sides)
(1) 1 x 12 x 21 in. (Bottom)
(1) 1 x 3 x 21 in. (Bottom)

Step 1: Cut the Game Pieces

Measure, mark, and cut the 2 x 4s to 10 ½ in. long. You should be able to cut 9 pieces out of each 8-ft. stud. You’ll need 54 pieces total.

Pro tip: Set up a stop block like I did here to make the repetitive cutting more efficient. With the stop block clamped in place, you won’t have to measure every board each time, but you should check the stop block periodically to ensure that it didn’t move and your measurements are still accurate.

Outdoor Block Stacking Game

Step 2: Sand the Game Pieces

I used a bench sander to make sanding quick and easy. Sand off all the splinters and rough edges. Be sure to wear protective gloves just in case your hand slips – the sanding belt is fast and can hurt if you’re not careful. You can then hand-sand the pieces with a 220-grit sandpaper, but I found that the bench sander made the game pieces smooth enough to handle and they slid easily when stacking.

Outdoor Block Stacking Game

Step 3: Build the Storage Box

Using the cut list above, measure, mark, and cut the storage box pieces to length. I was impressed that this RYOBI cordless sliding miter saw handled the wider boards with ease.

If you’re using pocket hole joinery, drill ¾-in. pocket holes into the bottom 1×12 and edge-join it with the 1 x 3 board with 1 ¼-in. pocket screws. These two boards will be the bottom of the box. Next, drill ¾-in. pocket holes into the ends of the two 1 x 12 short sides. Construct the box with 1 ¼-in. pocket screws.

If you’re not using pocket hole joinery, you can edge-join the two bottom boards with just wood glue. Clamp and allow the glue to dry overnight, making sure that the boards are flat and aligned. Then, pre-drill pilot holes and use 1 ¼-inch wood screws to construct the box.

Outdoor Block Stacking Game

I used my router to carve The Home Depot logo on the long sides of the box and then I attached them to the short sides and bottom with 1 ¼-inch brad nails and wood glue. I recommend that you always use wood glue when joining with nails. You can also join the sides with 1 ¼-in. pocket screws or wood screws, if you’d like.

Outdoor Block Stacking Game

Step 4: Attach the Handles

I picked up a couple of these storage chest handles from the hardware aisle. Find the midpoint on the short sides and mark it. Pre-drill pilot holes and attach the handles to the sides of the box with the included screws.

Outdoor Block Stacking Game

Pro tip: It’s helpful to have at least two drills so you don’t have to switch out drill and driver bits quite so often. I’m using the RYOBI hammer drill and impact driver here.

Outdoor Block Stacking Game